Theatre-solution Jury Base Seating Manuel d'utilisateur télécharger pdf (Page 27)

26 Specifications Lecture Seating

Lecture Seating Specifications

(This section pertains to the Aeron Lecture Seating model.)

PART 3 – OPTIONS

3.1 WORKSURFACES

Tables are to be a 3-ply warp resistant construction with a core of 1-1/8” thick 45-50 lb. density particle

board, a 0.020” Kraft backer sheet, and a face material of veneer. The grain is to run the length of the

worksurface.

3.2 MODESTY PANELS

Straight modesty panels are to be a 3-ply warp resistant construction with a core of 5/8” thick 45-50 lb.

density particle board. The face surfaces are to be 0.030” high-pressure laminate. On laminates with a

wood grain, the grain is to run horizontally.

Straight modesty panels are to be a 3-ply warp resistant construction with a core of 3/4” thick 45-50 lb.

density particle board. The face surfaces are to be veneer; the grain is to run horizontally.

Curved modesty panels are to be 3/8” thick medium density fiberboard with a 1/2” thick x 1” wide birch

plywood strip affixed to the bottom edge. The face surfaces are to be 0.030” high pressure laminate. On

laminates with a wood grain, the grain is to run horizontally.

Curved modesty panels are to be 3/8” thick medium density fiberboard with a 1/2” thick x 1” wide birch

plywood strip affixed to the bottom edge. The face surfaces are to be veneer; the grain is to run

horizontally.

3.3 END PANELS

End panels are to be a 3-ply warp resistant construction with a core of 1-1/8” thick 45-50 lb. density particle

board. The face surfaces are to be 0.030” high-pressure laminate.

B. The vertical edges are to be self-edged.

3.4

RMS

Each fixed arm shall have an armpad support and a yoke, both of die-cast aluminum with either a polished

or wrinkle-coat powder-coated epoxy finish. A support shall attach to the arm yoke with screws, and the

yokes shall attach with screws to slots in the swing arms, at the left and right of the chair back.

3.5 ELECTRICAL SYSTEM/DATA WIRE MANAGEMENT

Provide manufacturers standard modular electrical system for power distribution. All electrical modules

shall be manufactured from BX cable or liquid-tight BX cable, and shall have molded end connectors. The

modules shall connect to each other with a snap fitting designed so that they cannot be accidentally

disconnected during normal use. Each module shall be securely connected to the underside of the

worksurface.

The electrical system shall provide for a minimum of two separate circuits in each row and shall be

configured with two hot wires, a shared neutral and a shared ground.

Each row is to be powered at a single power entry point at the end of the row. The power feed shall be

manufactured from liquid-tight BX cable with a molded end connector at one end for connection into the

electrical system and a 6” pigtail at the other end for connection into the building’s electrical supply. Wiring

the power feed into the building’s electrical supply and the parts necessary to do so shall be done/supplied

by others and is not the responsibility of the manufacturer or its’ installers.

Provide manufacturers standard power/data module consisting of two electrical outlets and two Category 6

RJ-45 data jacks. Electrical and data jacks are to be black in color. The module shall be mounted in the

worksurface centered and shared between two seated occupants.

Provide necessary quantities of manufacturers standard wire management raceways for the concealment

and routing of data wiring. Data wiring is to be provided and installed by others and is not the responsibility

of the manufacturer or its’ installers.

3.6 COMPLIANCE WITH CALIFORNIA TECHNICAL BULLETIN 133

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 72 73

Commentaires sur ces manuels

Pas de commentaire

Theatre-solution Jury Base Seating Manuel d'utilisateur Page 27

Commentaires sur ces manuels

Produits connexes et manuels pour Meubles Theatre-solution Jury Base Seating