Theatre-solution Teatro Auditorium Seating Manuel d'utilisateur télécharger pdf (Page 24)

Teatro Auditorium Seating Specifications 23

Teatro C1 Specifications – Theatre Seating

(This section pertains to the Teatro C1 model. The seat assembly is fully-upholstered. The back assembly has an

inner-upholstered cushion and outer plywood panel with stained edges.)

PART 2 – PRODUCTS

2.1 SEATING

Provide from Theatre Solutions, Inc., 121 Park Avenue, Quakertown, PA 18951, the Teatro “C1” model

as follows:

1. Basic floor mounted chair.

2. Fully-upholstered seat.

3. Inner upholstered back.

4. Outer wood veneer back with stained edges.

5. Wood armrests.

6. Aisle lights where indicated on the drawings.

7. Wood veneer end panels where indicated on the drawings.

B. Model noted is based on the Theatre Solutions, Inc. Teatro “C1” model with the intent of establishing the

high level of quality required for the project. Other brands submitted for approval will be given

consideration provided that a full seating mock-up, along with a complete list of specification discrepancies

between the proposed substitution and the product specified is received at least 10 working days prior to

the bid date.

1. By offering a quote for this project, the bidder assumes full responsibility for complying with the

specifications for this project and shall be totally responsible for any expenses incurred if the

product quoted does not comply with the specifications.

C. Failure to comply with the warranty described in Part 4 of these specifications will be cause for

disqualification.

2.2 MATERIALS

A. Padding material shall be high resiliency polyurethane foam which conforms to the standards of the

California Bureau of Home Furnishings 117-75. The back shall be 1-3/4” thick. The seat shall be 3” thick.

B. Seating fabric shall be _______________________________________________ with the color to be

selected from the standard choice of colors. All upholstery shall be first quality without creases, stretch

lines, or wrinkles.

C. Exposed wood on the outer back panel shall be veneer. The panel edges shall be stained to match the

veneer faces. The arms shall be solid wood. All wood shall be stained in any of the manufacturer’s

standard finishes.

2.3 FABRICATION, GENERAL

A. Fabricate the theater seating in contoured form for maximum comfort using materials that are carefully

selected to be free from defects, objectionable projections, or irregularities. Smooth round corners and

edges to present the least possible snagging and pinching hazards.

2.4 MOUNTING

Fabricate seating units for floor attachment, using standards that have been manufactured to conform to

the slope of the floor while maintaining seat and back in same angular relationship to standards throughout.

2.5 METAL STANDARDS

A. Frame shall be 3/4” x 2” x 16 gauge cold-rolled welded steel tubing, and 5/16” x 3” hot-rolled steel plate,

and 11 gauge formed steel brackets welded into one integral freestanding structure upon which the seat,

back, and arms are assembled. Pivot and stop pins shall be machined from cold-finished steel to

tolerances of +0.000 -0.005. Floor mount plate shall be 5/16” thick hot-rolled pickled-in-oil steel plate with

two countersunk holes for 1/4-20 mounting screws.

2.6 UPHOLSTERED CHAIRS

A. General: Fabricate theater seating with padding and fabric covering. Equip each seat with a gravity self-

rising mechanism so that unoccupied seats return to an upright position perpendicular to the base line of

floor of auditorium. Spring compensating mechanism will not be acceptable. Chair profile with the seat in

the upright position and without a tablet arm, cannot exceed 18”. The chair profile with the seat in the

upright position and with a tablet arm, cannot exceed 24”.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Theatre-solution Teatro Auditorium Seating Manuel d'utilisateur Page 24

Commentaires sur ces manuels