Theatre-solution Teatro Auditorium Seating Manuel d'utilisateur télécharger pdf (Page 29)

28 Specifications Teatro Auditorium Seating

Teatro Specifications – Theatre Seating

(This section pertains to the Teatro C1 chair model.)

PART 3 – OPTIONS

3.1 END PANEL

Provide manufacturer’s standard end panel at the end of the row. The configuration of the panel shall

follow the angle of the frame and back at the rear, and shall be vertical at the front end. The panel shall be

constructed

of 3/4” thick plywood with veneer on both sides and 1/8” thick solid wood on the vertical edges.

The end panel shall be stained to match the outer wood seat, back, and armrests.

3.2 AISLE LIGHT

Aisle lights shall be provided in accordance to the lo

cations shown on the architectural drawings. The units

shall be of low voltage (24v) type and the light tube shall fit into a routed area on the underside of the

armrest. The chair frame shall be prepared to accept the power wire. The necessary access holes and

blank cover plates shall be provided. The chair manufacturer shall also provide the necessary

transformers. All wiring and electrical connections shall be conducted at the job site and shall be the

responsibility of others.

3.3 HARDWOOD EDGES, OUTER SEAT AND BACK

A. Outer plywood panels shall be trimmed in 1/8” thick hardwood on the top and vertical edges. The

hardwood shall match the face veneer species and be stained to match.

3.4 INSET UPHOLSTERY, BACK

Back Upholstery shall be inse

t to expose the veneer face on the inside of the outer back panel. The veneer

on the inside face on the back panel shall match the veneer species on the outside face and be stained to

match.

3.5 SEAT AND ROW IDENTIFICATION TAGS

A. Provide manufacturer’s standard shape brass number and letter plates. Font shall be Times Roman. The

size of the font on the seat number plates shall be 27pt; the size of the font on the row letter plates shall be

42pt. The number plates shall fit into a recessed area at the top edge of the seat. The row letter plates

shall fit into a recessed area at the back of the armrest.

3.6 REMOVABLE CHAIR

Provide manufacturer’s standard one, two, or three chair removable units which shall include an integrated

steel sled-base that is engineered to conform to the row radii and includes two through holes per chair for

floor mounting.

3.7 FREESTANDING REMOVABLE CHAIR

A. Provide manufacturer’s standard freestanding removable chair which shall include an integrated steel sled-

base that is engineered to conform to the row radii and includes extended length floor plates to allow the

chairs to remain stable with no physical attachment to the floor.

3.8 TABLET ARMS

A. Tablet arm shall be two-motion fold-away style, constructed of 1/2” medium density fiberboard, faced two

sides with matte black high-pressure laminate. The edges shall be finished with a vinyl T-molding trimmed

flush with both top and bottom surfaces.

3.9 POWER/DATA

Where indicated on the drawings, chair frames shall be equipped with a 115v/15amp power outlet and a

RJ-45 Category 6 data port located on the front of the armrest gusset. Wire raceways shall be

provided for

routing of the wires from chair to chair. All wiring and electrical connections shall be conducted at the job

site and shall be the responsibility of others.

3.10 BOOKRACKS

A. The bookrack shall be constructed of hardwoods and hardwood plywood.

Bookrack shall be assembled with

tongue and groove construction and finished with a catalyzed lacquer. The bookrack shall be attached to

the outer surface of the chair back. An optional attachment configuration shall consist of a steel weldment

attached to the chair leg. This configuration allows the bookrack to be located between chair backs.

3.11 COMPLIANCE WITH CALIFORNIA TECHNICAL BULLETIN 133

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Theatre-solution Teatro Auditorium Seating Manuel d'utilisateur Page 29

Commentaires sur ces manuels