Theatre-solution Teatro A1 Manuel d'utilisateur télécharger pdf (Page 2)

Teatro A1 Specifications – Theatre Seating

Page 2 of 5

3. Outer wood veneer seat and back with stained edges.

4. Wood armrests.

isle lights where indicated on the drawings.

6. Wood veneer end panels where indicated on the drawings.

Model noted is based on the Theatre Solutions, Inc. Teatro “A1” model with the intent of establishing the

high level of quality required for the project. Other brands submitted for approval will be given

consideration provided that a full seating mock-up, along with a complete list of specification discrepancies

between the proposed substitution and the product specified is received at least 10 working days prior to

the bid date.

By offering a quote for this project, the bidder assumes full responsibility for complying with the

specifications for this project and shall be totally responsible for any expenses incurred if the

product quoted does not comply with the specifications.

Failure to comply with the warranty described in Part 4 of these specifications will be cause for

disqualification.

2.2 MATERIALS

Padding material shall be high resiliency polyurethane foam which conforms to the standards of the

California Bureau of Home Furnishings 117-75. The back shall be 1-3/4” thick. The seat shall be 3” thick.

Seating fabric shall be _______________________________________________ with the color to be

selected from the standard choice of colors. All upholstery shall be first quality without creases, stretch

lines, or wrinkles.

Exposed wood on the outer back panel shall be veneer. The panel edges shall be stained to match the

veneer faces. The arms shall be solid wood. All wood shall be stained to match the architect’s sample.

2.3 FABRICATION, GENERAL

Fabricate the theater seating in contoured form for maximum comfort using materials that are carefully

selected to be free from defects, objectionable projections, or irregularities. Smooth round corners and

edges to present the least possible snagging and pinching hazards.

2.4 MOUNTING

Fabricate seating units for floor attachment, using standards that have been manufactured to conform to

the slope of the floor while maintaining seat and back in same angular relationship to standards throughout.

2.5 METAL STANDARDS

Frame shall be 3/4” x 2” x 16 gauge cold-rolled welded steel tubing, and 5/16” x 3” hot-rolled steel plate,

and 11 gauge formed steel brackets welded into one integral freestanding structure upon which the seat,

back, and arms are assembled. Pivot and stop pins shall be machined from cold-finished steel to

tolerances of +0.000 -0.005. Floor mount plate shall be 5/16” thick hot-rolled pickled-in-oil steel plate with

two countersunk holes for 1/4-20 mounting screws.

2.6 UPHOLSTERED CHAIRS

General: Fabricate theater seating with padding and fabric covering. Equip each seat with a gravity self-

rising mechanism so that unoccupied seats return to an upright position perpendicular to the base line of

floor of auditorium. Spring compensating mechanism will not be acceptable. Chair profile with the seat in

the upright position and without a tablet arm, cannot exceed 18”. The chair profile with the seat in the

upright position and with a tablet arm, cannot exceed 24”.

Seat Construction: Solid seat bottom construction comprised of a curved plywood veneer outer panel

fastened solidly and without voids to an inner structural plywood panel. The outer panel shall be 15mm

thick, faced one side with Grade A veneer centered across the width of the panel, and exposed plywood

laminations along the edges. The inner panel shall be 5/8” thick. Both shall be electronically glued

hardwood plywood and shall be fastened together with bayonet hanging brackets at the top and two steel

angles at the bottom, resulting in a rigid connection with no visible fasteners. The veneer face and edges

of the outer panel shall be stained to match the architect’s sample. The padding material shall be 3” thick

polyurethane foam, shall be glued to the inner panel, and shall conform to the California Bureau of Home

Furnishings Technical Bulletin 117. The complete seat assembly shall be supported by two 7 gauge

formed steel mounting brackets which will attach the seat assembly to the hinges on the standards. The

seat shall have a built-in counterweight to insure automatic self-rising without the aid of springs. Arch-

spring construction will not be acceptable.

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Theatre-solution Teatro A1 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Meubles Theatre-solution Teatro A1